R/S Run Stop Port (3pin Fischer type) 

A simple close contact run/stop for standard non-powered close contact 3 Pin Fischer hand grip triggers, pickle triggers, Nucleus FIZ R/S, etc

There is no available 12/24v power on this port. It will not power camera accessories.

C-Motion, Arri, *Teradek RT, Preston, Tilta Nucleus and others require a cable that terminates to Fischer 3 Pin to enable remote run / stop. Some WFF systems will require setup in the menu to enable close contact triggering.

*For Teradek use the RT Latitude MDR ARRI Run/Stop Cable MFR #11-1375 on the last motor in the chain.

Pin1:GND, pin2:N/C, pin3:GPI

Timecode IN/OUT Port (5pin LEMO type)

Standard wiring for timecode in and out via 0B 5 Pin

Pin1:GND, pin2:LTC-IN, pin3:N/C, pin4:N/C, pin5:LTC-OUT

CTRL (4pin LEMO type)

Standard wiring for RED CTRL on 00B 4 Pin

Pin1:GND, pin2:UART-RX, pin3:GPO, pin4:UART-TX

If using SmallHD KOMODO control you will need this SmallHD Control Cable https://smallhd.com/products/red-ctrl-4-pin-to-smallhd-5-pin-usb-cable and SmallHD KOMODO Control Software to directly connect Mutiny IO to SmallHD Focus Pro, Cine 7, and 702 Touch monitors, etc.

Genlock (BNC)

Genlock on standard BNC connector

Center pin: Signal, BNC shell: Ground

KOMODO or V-RAPTOR EXT (9 Pin Lemo type)

Mutiny IO 9 Pin 0B connector to mate with EXT 9 Pin 0B

Mounting

3 x 1/4-20 mounting holes .5” on center

2 x tether points on top

1 x tether point on the bottom (for bongo tie or equivalent)

IO units include 2 x 1/4-20 mounting screws and now include a Red Bongo Tie

 Size, Weight and Mounting

Size: 3” x 1.75” x 1” 

Weight: 2.7oz 

3 x 1/4-20 mounting holes .5” on center, 2 x tether points on top, 1 x tether point on the bottom (for bongo tie or equivalent) IO units include 2 x 1/4-20 mounting screws and now include a Red or Lava Bongo Tie.

R/S Run Stop Port (3pin Fischer type) 

Close contact run/stop with power on pin 2 for 3 Pin Fischer hand grip triggers, pickle triggers, Nucleus FIZ R/S, etc 

There is unregulated power on this port (whatever your battery is providing). It will power camera accessories.

C-Motion, Arri, *Teradek RT, Preston, Tilta Nucleus and others require a cable that terminates to Fischer 3 Pin to enable remote run / stop. Some WFF systems will require setup in the menu to enable close contact triggering. *For Teradek use the RT Latitude MDR ARRI Run/Stop Cable MFR #11-1375 on the last motor in the chain.

Pin1:GND, pin2: VOLTAGE, pin3:GPI

Timecode with Genlock Combo Port (5pin 0B LEMO type)

Standard wiring for timecode and also includes genlock.

Pin1:GND, pin2:LTC-IN, pin3:N/C, pin4:GENLOCK, pin5:LTC-OUT

CTRL (4pin 00B LEMO type)

Standard wiring for RED CTRL on 00B 4 Pin

Pin1:GND, pin2:UART-RX, pin3:GPO, pin4:UART-TX

If using SmallHD KOMODO control you will need this SmallHD Control Cable https://smallhd.com/products/red-ctrl-4-pin-to-smallhd-5-pin-usb-cableand SmallHD KOMODO Control Software to directly connect Mutiny IO to SmallHD Focus Pro, Cine 7, and 702 Touch monitors, etc.

9 Pin EXT Passthrough (9P 0B Lemo type)

9 Pin 0B passthrough connector allows for expansion or to use 9 pin EXT devices with the Battery IO.  Example: Small HD camera control with 9 pin cable.  Trigger with 9 pin cable, etc. 

Mounting

Battery IO for KOMODO mounts directly to the BP battery slots on the RED KOMODO.  It only requires the left lock button to unlock.  The 9P EXT cable mounts to the EXT port and the Power cable mounts to the KOMODO 2 pin power input. 

 Size, Weight and Mounting

8.1oz (1/2 pound), 85mm (3.34") wide, 48mm (1.8")deep, 81mm (3.18") tall (at top of record button)

The NANO & NANO+

R/S Run Stop Port (3pin Fischer type) 

A simple close contact run/stop for standard non-powered close contact 3 Pin Fischer hand grip triggers, pickle triggers, Nucleus FIZ R/S, etc

There is no available 12/24v power on this port. It will not power camera accessories.

C-Motion, Arri, *Teradek RT, Preston, Tilta Nucleus and others require a cable that terminates to Fischer 3 Pin to enable remote run / stop. Some WFF systems will require setup in the menu to enable close contact triggering.

*For Teradek use the RT Latitude MDR ARRI Run/Stop Cable MFR #11-1375 on the last motor in the chain.

Pin1:GND, pin2:N/C, pin3:GPI

Timecode with Genlock Combo Port (5pin 0B LEMO type)

Standard wiring for timecode and also includes genlock. 

Pin1:GND, pin2:LTC-IN, pin3:N/C, pin4:GENLOCK, pin5:LTC-OUT

CTRL (4pin 00B LEMO type)

Standard wiring for RED CTRL RCP2 on 00B 4 Pin

Pin1:GND, pin2:UART-RX, pin3:GPO, pin4:UART-TX

If using the 4pin port for SmallHD KOMODO control you will need this cable https://smallhd.com/products/red-ctrl-4-pin-to-smallhd-5-pin-usb-cableand SmallHD KOMODO Control Software to directly connect Mutiny IO to SmallHD Focus Pro, Cine 7, and 702 Touch monitors, etc. If your SmallHD monitor has a 9 pin control cable you will want the NANO+

NANO+ features this additional port:

9 Pin EXT Passthrough (9P 0B Lemo type)

9 Pin 0B passthrough connector allows for expansion or to use 9 pin EXT.  Example: Small HD camera control with 9 pin cable.  Trigger with 9 pin cable, etc. 

MOUNTING

Flat mount 2x 1/4-20 mounting holes .5" on center

90 degree mount 2x 1/4-20 mounting holes .5" on center

15mm rod mount with 90 degree fore/aft/side mounting

Flat and 90 degree mount come with 2x 1/4-20 3/8" long screws.

Each mount allows for 90 degree rotation in four directions for NANO and in three directions for NANO+

Size and Weight

1"x 1" x 7/8"

NANO is 0.8oz, NANO+ is 1.5oz